ACE_TTY_IO::ACE_TTY_IO::Serial_Params Struct Reference

#include <TTY_IO.h>

List of all members.

Public Member Functions

Serial_Params (void)

Public Attributes

int baudrate

int xonlim

int xofflim

unsigned int readmincharacters

int readtimeoutmsec

const char * paritymode

bool ctsenb

unsigned char rtsenb

bool xinenb

bool xoutenb

bool modem

bool rcvenb

bool dsrenb

bool dtrdisable

unsigned char databits

unsigned char stopbits

Constructor & Destructor Documentation

ACE_TTY_IO::ACE_TTY_IO::Serial_Params::Serial_Params ( void )

int ACE_TTY_IO::ACE_TTY_IO::Serial_Params::baudrate

Specifies the baudrate at which the communnication port operates.

bool ACE_TTY_IO::ACE_TTY_IO::Serial_Params::ctsenb

Enable & set CTS mode. Note that RTS & CTS are enabled/disabled together on some systems (RTS/CTS is enabled if either ctsenb or rtsenb is set).

unsigned char ACE_TTY_IO::ACE_TTY_IO::Serial_Params::databits

Data bits. Valid values 5, 6, 7 and 8 data bits. Additionally Win32 supports 4 data bits.

bool ACE_TTY_IO::ACE_TTY_IO::Serial_Params::dsrenb

Controls whether DSR is disabled or enabled (Win32).

bool ACE_TTY_IO::ACE_TTY_IO::Serial_Params::dtrdisable

Controls whether DTR is disabled or enabled.

bool ACE_TTY_IO::ACE_TTY_IO::Serial_Params::modem

Specifies if device is a modem (POSIX). If not set modem status lines are ignored.

const char* ACE_TTY_IO::ACE_TTY_IO::Serial_Params::paritymode

Specifies the parity mode. POSIX supports "none", "even" and "odd" parity. Additionally Win32 supports "mark" and "space" parity modes.

bool ACE_TTY_IO::ACE_TTY_IO::Serial_Params::rcvenb

Enable/disable receiver (POSIX).

unsigned int ACE_TTY_IO::ACE_TTY_IO::Serial_Params::readmincharacters

Specifies the minimum number of characters for non-canonical read (POSIX).

int ACE_TTY_IO::ACE_TTY_IO::Serial_Params::readtimeoutmsec

Specifies the time to wait before returning from read. Negative value means infinite timeout.

unsigned char ACE_TTY_IO::ACE_TTY_IO::Serial_Params::rtsenb

Enable & set RTS mode. Note that RTS & CTS are enabled/disabled together on some systems (RTS/CTS is enabled if either ctsenb or rtsenb is set).

0 = Disable RTS.
1 = Enable RTS.
2 = Enable RTS flow-control handshaking (Win32).
3 = Specifies that RTS line will be high if bytes are available for transmission. After transmission RTS will be low (Win32).

unsigned char ACE_TTY_IO::ACE_TTY_IO::Serial_Params::stopbits

Stop bits. Valid values are 1 and 2.

bool ACE_TTY_IO::ACE_TTY_IO::Serial_Params::xinenb

Enable/disable software flow control on input.

int ACE_TTY_IO::ACE_TTY_IO::Serial_Params::xofflim

Specifies the maximum number of bytes in input buffer before XOFF char is sent. Negative value indicates that default value should be used (Win32).

int ACE_TTY_IO::ACE_TTY_IO::Serial_Params::xonlim

Specifies the minimum number of bytes in input buffer before XON char is sent. Negative value indicates that default value should be used (Win32).

bool ACE_TTY_IO::ACE_TTY_IO::Serial_Params::xoutenb

Enable/disable software flow control on output.

The documentation for this struct was generated from the following files: